26th
Annual Batson Bladesmithing Symposium 2014
First day off in who knows how long??? I left W’boro at 06:45am. The ride was nice, and weather was fine. Got down to Tannehill State Park
by 10:30am and registered right away. I found a camp site close to all the
action and a small creek, got my sales table out, set my tent up and ate some
lunch. The next thing was to hit the
vendors before the first afternoon class.
Bought some curly maple blocks and steel.
Batson Bladesmithing Symposium is held at Tannehill State Park
near McAlla, Alabama www.tannehill.org
. This was the 26th year the
event took place. It was held April
10-13. The cost for the weekend is $100
which includes a 1 year membership to the Alabama Forge Council, the bi-monthly
subscription to their magazine Bituminous Bits, all the classes Friday-Sunday,
camping at the park and a BBQ dinner. As
the name implies it is primarily forge oriented. It is sponsored by the Alabama Forge Council www.alaforge.org and the American
Bladesmith Society www.americanbladesmith.com
.
Demonstrators from around the country come to teach at the
facilities. This place is outfitted with
everything necessary to teach all aspects of knife making and forging.
It all starts on Thursday with a demonstrator’s dinner. Registration and check in begins bright and
early on Friday at 7:00am with classes and demonstrations starting at
8:00am. Classes run from 8-10am, 10-12pm,
1-3pm and 3-5pm Friday. Saturday and Sunday classes run 8-10am & 10-12pm. There are 3-5 classes to choose from for each
time slot.
Your choice of classes include: forging, blade grinding,
handle & guard construction. wire inlay, leather sheaths, jigs &
fixtures, knife design, many Damascus
techniques, engraving, scrimshaw and more.
This is by no means all that are offered. Most of the classes are offered more than
once so the chances are good that you’ll get to attend all the ones you want
to.
The classes I took Friday afternoon were both taught by
Master Smith Joe Keeslar. The first was
on leather sheaths. He has done
leatherwork since he was a teen. The
quality of his work is amazing and makes it look so easy. Joe went over design, cutout and putting
together a leather sheath from start to finish.
He demonstrated different ways of stitching as well as sheath
embellishments. The second class was on
knife design. We all discussed primary
uses for knives and their particular design criteria. Joe had us each design a large and small
knife. Our designs were constructively
critiqued and we all ended up with nicer designs. He asked us to create the knives we designed
and bring them back next year to show.
You will find tailgate sales around the grounds. There are all kinds of knife related wares
for sale. Some of the things this year
included grinders, anvils, post vices, hammers, forges, firebrick, abrasive
belts, leather, books, dvd’s and lots of steel.
Much of the steel is round bar for forging. Aldo Bruno drives down from New Jersey to sell his steel. His truck is loaded with flat bar. He sells quite a bit of steel to make Damascus. He usually makes a killing just after any Damascus class lets
out. The best part is no shipping charge
when you buy from any of the vendors.
Anyone is allowed to put their materials out for sale and you just price
everything and leave a bucket to put the money in and you’re good to go. It is best to buy what you want fast because
a lot of it goes quick and then it’s not available.
I sat and talked with Aldo Bruno for a while. He talked about some rough times this past
winter and his hopes of doing more for all the knife makers out there. His steel is some of the best available and
he has recently purchased a waterjet machine.
He’s in the process of getting it ready to cut knife blanks out. Many companies with a waterjet cater to
differing industries, but Aldo wants to work for the knife makers alone. If you produce a knife or knives over and
over, the cutout work can be done on a waterjet. The best part is you can buy your steel, have
the blades cut out there and shipped to you from one company. That will save a bunch on buying steel one
place, shipping to another and paying for return shipping. If you make a bunch of the same knife, this
process can save you time and money. I
can see having my regular hunters and utility knives cut out, but most of mine
are one-offs so those could only be done by me.
Aldo said the services should soon be offered on his website www.newjerseysteelbaron.com.
There are going to be more forged knives coming out so it
just may be the time to join the ABS. I’ve
wanted to join for some time and after talking to JS Dwight Phillips from Lawrenceburg, TN
he made me want to join now even more.
Dwight is a Journeyman Smith in the ABS and has his 5 knives almost
ready to judge for his Master Smith stamp.
After classes were done on Friday there was a free BBQ
offered from 5-7pm on the other side of the park. They had burgers, smoked sausage, hot dogs
and some of the best baked beans I ever ate.
The comradery was great and all the talk was about knives and knife
making.
The evening festivities commence back at the Vulcan pavilion
with a cutting competition. Everyone is
allowed to enter the competition. All
you need is a sharp knife with a forged blade 10 inches or under & total
length not over 15 inches. The handle
must be pinned and have a wrist thong for safety. There were 8 guys that entered and their
knives were checked over by the safety official. The events are random each year and this year
6 events were scheduled. 1st
event was to take one chop at a 2x4 at a 45 degree angle. The deeper you chopped the more points you
got. 2nd event you had
to stab the knife tip 1/8-1/4 inch into a 2x4 and pry out a chip. Most did it but one tip was broke off. Glad it wasn’t my knife. 3rd event was to poke a
tennis ball with your knife tip and lift it to shoulder height. 4th
event had a roll of toilet paper with a few sheets hanging down and you had to
slice it cleanly with out tearing. 5th
event you had to chop a ping pong ball and the 6th event was
chopping a golf ball. The overall winner
for the night was Russell White. I gotta
tell y’all that these events sound way easier than they are to perform. I competed in 2011 and only accomplished one
of the required tasks from that year. If
you haven’t done any of these things give it a try. There are folks that are professional cutters
and can do amazing things with their knives.
Saturday started with classes at 8am. The class I took was taught by Mickey Wise
and was on Old Timey Knives. Mickey went
through the forging process of a small blade.
His hammer blows were easy and it seemed like he hardly hit the steel. Next he drilled a piece of antler for
it. He then broached the antler to fit
the tang snugly using home made scrapers, discussing how we can make or
own. Mickey got out a blade he had previously
heat treated and showed us how to pour a pewter bolster. From that point the bolster had to be cleaned
up and feathered into the antler handle.
The weather in Alabama
was beautiful with morning temps of low 50’s and daytime temps of around 80 degrees.
Classes only go till noon on Saturday with a knife show to
start the afternoon off. The knife show
is open from 1-3pm for any demonstrator or attendee to put their knives out for
display/sale. It is held in the open on
picnic tables, with a large pavilion nearby in case of inclement weather. There were about 15 tables set up with a lot
of nice knives being shown. The show
usually begins with Rail Road Spike Knife judging. I’d have to say there were probably a dozen
RR Spike knives out. One was made from Damascus and one had an MS
stamp on it.
Next up is the auction conducted by Col. Tim Ryan. It begins at 3:00pm. Everything auctioned off is donated for Iron
In The Hat by demonstrators, attendees and vendors. All proceeds go to the Alabama Forge Council
building fund. Many interesting items
turn up for the auction as well as some very nice knives. Joe Keeslar offered a 3 day workshop at his shop
which sold for over $600. This is an
interesting part of the weekend.
Saturday evening held the Heat Treat Extravaganza. Dr. Batson explained heat treat curves and
properties of steel during the process.
He then proceeded to heat treat a number of blades with the emphasis on
everyone seeing the transformations that take place while heating. Canola oil was used to quench the blades so
we could see what happened in the oil as the steel was being cooled down. The blades were put into vermiculite until
ready to put in the oven.
Usually Tannehill Iron Works does an iron pour on the
Saturday of the Bladesmith Symposium which was scheduled on the website. There was flooding the weekend before so it
had to be cancelled. A group of
volunteers prepare the furnace and keep it burning. It is opened up after dark with the molten
steel flowing into crucibles carried by two-man teams and poured into small
castings. You pay a fee of about $20-25
to create your own flat castings. People
from all over the park do their castings during the day and they get to take
them at the end of the night. I watched
in 2011 and hoped to do a casting of my touchmark this year. There will be another pour Sept. 7th
when the Alabama Forge Council has their fall conference at the park. Tannehill has a lot of history, so if you
have a chance to go through the park, I’m sure you will enjoy it.
The final day only has 3 classes at 8-10am and 3 classes at
10am-12pm. Things are winding down and a
lot of folks are packing up and heading out.
If you ever have the opportunity to attend the Batson
Bladesmithing Symposium go for it. The
amount of knowledge there is amazing.
Any thing you want to know about forging knives or Damascus is available by simply asking. You won’t be disappointed
No comments:
Post a Comment